Allen-sports 522RR User Manual download pdf

Model 522RR Instructions

English - Page 1

WARNING: Bikes or rack falling in road can cause serious accidents resulting in bodily injury—do not use rack on any

vehicle on which it can not be properly mounted as described in this instruction sheet.

 Rack should only be used on vehicles with 1 1/4” or 2” receiver hitches.

 NEVER use on trailers or front of vehicles.

 Bikes must be tied to rack using tie-downs, or additional straps if necessary.

 Check periodically during use that all bolts and pins are tight, and that rack and bicycles are secure.

 Never carry more than 2 bikes (max capacity 70 LB) - no tandems, mopeds, or recumbents. Car tail lights must

remain visible.

 Drive conservatively, especially over bumps. Never use off-road.

 Do not use if any part of the rack is damaged, worn, or missing. Contact R. A. Allen Co., Inc. for replacement parts.

CAUTION: Use Allen 522RR only in accordance with local motor

vehicle and traffic regulations.

 Install rack and load bicycles only at a safe distance away

from moving traffic.

 Make sure that all of rack and bicycles are kept at a safe dis-

tance from road and hot exhaust.

 Only operate vehicle with rack in an upright, locked position.

 Bicycles should never extend beyond sides of vehicle.

 Remove rack from car, or fold carry arms down when not in

use.

PARTS:

TOOLS REQUIRED: 2—9/16” WRENCH & 2—3/4” WRENCH;

OR 2—ADJUSTABLE WRENCHES

522RR B

OX SHOULD CONTAIN THE

FOLLOWING ITEMS:

1—C

ARRY ARM

SSEMBLY

1—RR P

OST

1—H

ARDWARE KIT,

CONTAINING

2—3/8” X 2 1/2” BOLT

1—3/8”

X 3” BOLT

4—3/8” L

OCK NUT

1—1/2” L

OCK NUT

1—1/2” N

O-WOBBLE

OLT

ASSEMBLING RACK:

STEP 1

STEP 2

INSERT LOWER PORTION OF RR POST INTO

ITCH INSERT SO THAT THE HOLES AT THE BOT-

TOM

OF EACH PART LINE UP.

INSERT THE 3/8” X 3” BOLT THROUGH THE

HOLE, AND THREAD 1—3/8” LOCK NUT ONTO

THE END OF THE BOLT.

PIVOT THE RR POST INTO THE UPRIGHT POSI-

TION, SO THAT THE UPPER HOLES LINE UP. IN-

SERT

THE QR CLIP THROUGH THESE HOLES, AND

SECURE THE WIRE RETAINER CLIP.

TIGHTEN NUT AND BOLT FIRMLY USING TWO

WRENCHES.

HITCH INSERT

RR POST

3/8” LOCK

3/8” X 3”

OLT

INSERT CARRY ARM ASSEM-

BLY

INTO UPPER PORTION

OF RR POST, LINING UP

THE HOLES IN EACH PART.

INSERT THE 3/8” X 2 1/2”

BOLTS THROUGH EACH

HOLE, AND THREAD 1—

3/8”

LOCK NUT ONTO THE

END OF THE BOLTS.

TIGHTEN NUT AND BOLT

FIRMLY USING TWO

WRENCHES.

NOTE:

UPON COMPLETION,

BOTH PARTS SHOULD BE

FIRMLY JOINED TOGETHER.

CARRY ARM ASSEMBLY

3/8” X 2 1/2”

OLT

QR CLIP

IMPORTANT:

WHEN RACK IS IN AN

UPRIGHT POSITION,

IRE RETAINER ON QR

LIP SHOULD ALWAYS BE

IN A CLOSED POSITION

TO KEEP RACK FROM

FALLING OVER DURING

USE.

1—HITCH INSERT W/

FILLER PLATES

1—3/8” NO-WOBBLE

OLT

FILLER PLATES

1 2

Summary of Contents

Page 1 - ASSEMBLING RACK:

Model 522RR Instructions English - Page 1 WARNING: Bikes or rack falling in road can cause serious accidents resulting in bodily injury—do not use rac

Page 2 - SECURING BIKES TO RACK:

Model 522RR Instructions English - Page 2 D. FOLDING UP CARRY ARMS: E. LOADING BICYCLES ON RACK: TO FOLD UP CARRY ARMS, REMOVE THE QR CLIP FROM THE C

Allen-sports 522RR User Manual

Browse online or download User Manual for For bicycles Allen-sports 522RR. Allen Sports 522RR User Manual

Summary of Contents

More documents for For bicycles Allen-sports 522RR

Comments to this Manuals

Allen-sports 522RR User Manual

Browse online or download User Manual for For bicycles Allen-sports 522RR. Allen Sports 522RR User Manual

Summary of Contents

More documents for For bicycles Allen-sports 522RR

Comments to this Manuals

Related products and manuals for For bicycles Allen-sports 522RR